---
title: "Stacking: Packing Method | Pack Studio User Guide"
url: "https://www.pack-studio.com/wiki/stacking"
description: "Stacking fills nested columns of parts, upright or on their side, then tiles them across the box. Built for tubes, sleeves, cans and stamped sheet metal."
updated: "2026-11-17"
type: "TechArticle"
---

Packing Method /// User Guide

# Stacking

Stacking fills nested columns of parts, upright or on their side, then tiles them across the box. Built for tubes, sleeves, cans and stamped sheet metal.

**Best for:** Tubes, sleeves, cans and sheet metal that nest along one axis.

Stamped parts such as trays, brackets and panels are mostly empty space inside their bounding boxes, but they nest. Stacking takes advantage of that. It fills a single nested column with as many parts as fit, upright or on its side, then tiles that column across the box.

## How it works

Release 1.10 rebuilt the column builder from the ground up. Stacks can run vertically up the box or horizontally across the floor, and the engine adjusts part orientation automatically to find the densest stack. Stacking works with [partitions](https://www.pack-studio.com/wiki/partitions), layer dividers and [molded trays](https://www.pack-studio.com/wiki/molded-tray).

## Settings

- **Stacking direction:** vertical or horizontal.
- **Maximum tilt angle:** 0 to 45 degrees.
- **Spacing:** between parts, between stacks and between layers.
- **Maximum parts per stack:** caps a column for handling or weight.
- **Layers:** tier stacks into layers with separators.

## In the published studies

| Case | Container | Parts per container | Cost per part |
|---|---|---|---|
| Steel bracket | 12 × 12 × 8 in carton | 14 to 23 (1.6×) | $0.081 to $0.054, 33% lower[^1] |
| Car door panel | 52 × 48 × 58 in returnable rack | 75 to 134 (1.8×) | $0.577 to $0.348, 40% lower[^2] |

The door panel result also shrank the returnable rack fleet from 59 racks to 33. The parts, containers and freight stayed the same; only the stacking decision changed.

## When to use it

- Tubes, sleeves and cans.
- Stamped sheet metal, trays and panels that nest along one axis.
- Returnable racks where a denser stack shrinks the fleet.

## Questions about Stacking

### Can stacks run horizontally?

Yes. Since release 1.10, stacks can run vertically up the box or horizontally across the floor.

### How much can Stacking save on stamped parts?

In the published study, Stacking cut cost per part by 33% for a steel bracket and 40% for a car door panel, with the same containers and freight.

## Related

- [Why teams use Stacking](https://www.pack-studio.com/features/stacking)
- [Flexible Layering](https://www.pack-studio.com/wiki/flexible-layering)
- [Partitions](https://www.pack-studio.com/wiki/partitions)
- [Molded Tray](https://www.pack-studio.com/wiki/molded-tray)
- [Returnable Assets](https://www.pack-studio.com/wiki/returnable-assets)
- [Stacking: Minimizing the Shipping Cost for Stamped Parts](https://www.pack-studio.com/post/stacking-minimizing-the-shipping-cost-for-stamped-parts)
- [Pack Studio 1.10 Software Release Notes](https://www.pack-studio.com/post/pack-studio-1-10-software-release-notes)

[^1]: Cost per part, Stacking versus Flexible Layering: 33% lower. Same box and board grade. Source: [Stacking: Minimizing the Shipping Cost for Stamped Parts](https://www.pack-studio.com/post/stacking-minimizing-the-shipping-cost-for-stamped-parts), 2026-08-17.
[^2]: Cost per part, Horizontal Stacking versus the unstacked baseline in a returnable rack: 40% lower. Same rack and freight. Source: [Stacking: Minimizing the Shipping Cost for Stamped Parts](https://www.pack-studio.com/post/stacking-minimizing-the-shipping-cost-for-stamped-parts), 2026-08-17.
