---
title: "Fastener and Industrial Parts Packing Software | Pack Studio"
url: "https://www.pack-studio.com/industries/industrial-parts-and-fasteners"
description: "Pack Studio counts, packs and costs fasteners, clips, castings and machined parts from CAD, from bulk-filled totes to protected cartons, on landed cost per part."
updated: "2026-11-19"
type: "WebPage"
---

Industries /// Industrial Parts and Fasteners

# Packaging Optimization for Industrial Parts and Fasteners

**Small parts. Big freight bills.**

Fasteners, clips, castings and machined parts ship in huge volumes, so a few more parts per tote or a lighter board grade repeats on every shipment. Pack Studio counts, packs and costs them from CAD.

## Where packaging cost hides.

- **Bulk counts are guesses:** totes are filled by volume and a fill factor, not by the actual part geometry.
- **High mix:** hundreds of part numbers, each needing its own pack, container and count.
- **Finished surfaces:** machined and plated parts scuff in transit and need protection that is priced in.
- **Weight-limited freight:** on dense steel parts, the truck's weight limit often decides the pack.

## Built for parts that ship by the thousand

Industrial manufacturers and distributors ship small, dense and often identical parts in very high volumes. The packaging decisions look minor, a tote size here, a board grade there, but they repeat on every shipment for years.

Pack Studio handles the full range in one tool: loose parts poured into totes with [Bulk](https://www.pack-studio.com/features/bulk) packing, finished parts protected with [Compartment](https://www.pack-studio.com/features/compartment) cells and [Partitions](https://www.pack-studio.com/features/partitions), and cartons sized with [Optimize Box](https://www.pack-studio.com/features/optimize-box). Every option is ranked on cost per part with the truck's cube or weight limit included, which matters for dense steel parts.

## The published evidence

Two of Pack Studio's published studies use industrial parts. A stamped steel bracket shipped at 33% lower[^1] cost per part with Stacking, and a steel pipe connector shipped at 15% lower[^2] cost per part with Optimal orientation. The same tests can run on your parts.

## Where Pack Studio fits.

- [Bulk](https://www.pack-studio.com/features/bulk): Bulk packing runs a physics simulation that pours loose parts into a container and lets gravity, contact and friction settle them.
- [Compartment](https://www.pack-studio.com/features/compartment): Compartment packing gives each part its own rectangular cell, one per cell or two nested head to tail, so finished parts never touch.
- [Partitions](https://www.pack-studio.com/features/partitions): Pack Studio generates a divider set sized to the actual pack, so every part gets its own walled cell.
- [Optimize Box](https://www.pack-studio.com/features/optimize-box): Optimize Box searches a window of carton dimensions around your part, protective packaging, pallet and ergonomic limits, and returns the box with the lowest landed cost per part.
- [Truckload Optimization](https://www.pack-studio.com/features/truckload-optimization): Pack Studio loads pallets into trucks and shipping containers, such as a 53 ft dry van, and shows parts per truck and whether the load is limited by cube or by weight.
- [Cost Per Part and ROI](https://www.pack-studio.com/features/cost-per-part-and-roi): Pack Studio reduces every packaging option to one figure: box, protective packaging, pallet and freight divided across the parts on board.

**Proof status:** No published industrial-parts case study yet. The engine and cost model are the same ones Lucid Motors runs across vehicle launches, and two of the published studies use industrial parts: a stamped steel bracket and a steel pipe connector.

## Questions

### Can Pack Studio count loose parts in a tote?

Yes. Bulk packing simulates parts poured into the container and settling under gravity and friction, then counts and costs the result.

### What if a part has no CAD yet?

The Part Designer describes it as a box, sphere or cylinder, so a pack can be estimated before CAD exists.

[^1]: Cost per part, Stacking versus Flexible Layering: 33% lower. Same box and board grade. Source: [Stacking: Minimizing the Shipping Cost for Stamped Parts](https://www.pack-studio.com/post/stacking-minimizing-the-shipping-cost-for-stamped-parts), 2026-08-17.
[^2]: Cost per part, Optimal orientation versus best of six hand-picked orientations: 15% lower. Same carton, pallet, truck and freight as the figurine study. Source: [Optimal Orientation: Packing Complex Parts at the Best Angle](https://www.pack-studio.com/post/optimal-orientation-packing-complex-parts-at-the-best-angle), 2026-08-07.
