---
title: "Flexible Layering: 3D Interlocking Part Packing | Pack Studio"
url: "https://www.pack-studio.com/features/flexible-layering"
description: "Flexible Layering packs irregular parts in a 3D lattice so they interlock in every direction, reaching the highest fill on awkward shapes, ranked on cost per part."
updated: "2026-11-19"
type: "WebPage"
---

Packing methods /// Available now

# Flexible Layering

**Interlock in every direction.**

Flexible Layering arranges copies of a part in a three-dimensional lattice, so they interlock across every axis instead of sitting in separate layers. It reaches the highest fill on awkward shapes, and Pack Studio ranks every lattice on cost per part.

- **Best for:** Irregular, organic or nestable parts where fill rate matters more than a uniform stack.
- **Status:** Available now
- **You get:** 3D lattice per container, Fill rate and density, Cost per part

## The problem with grids

A grid treats every part like a box. For a bracket, a casting or a molded part with arms and pockets, most of that box is air, and air is what you pay to ship. Teams know denser arrangements exist, but finding one by hand means hours of trial in CAD for a single part.

## What Pack Studio does

Flexible Layering searches a lattice of positions and rotations so copies of the part interleave in all three directions. Each candidate lattice is costed with the same engine as a full analysis, including protective packaging, pallet and freight, so the winner is the least expensive to ship rather than the most impressive geometry.

It works with Optimal orientation, which searches 3D rotations for the densest pose, and with [Nesting and Repacking](https://www.pack-studio.com/features/nesting-and-repacking), which fills the space a lattice leaves behind.

## Know when to use something else

Density is not the only goal. For stamped parts that nest along one axis, [Stacking](https://www.pack-studio.com/features/stacking) often wins: in Pack Studio's published bracket study, Stacking fit 23 parts per carton against 14 with Flexible Layering, for 33% lower[^1] cost per part. Because both run in the same tool, you do not have to guess. Run both and let the cost ranking decide.

## Who uses it

Engineers packing irregular parts on high-volume lanes, where freight dominates the cost and the pack is unloaded by automation or dumped rather than picked layer by layer.

## Questions about Flexible Layering

### When does Flexible Layering beat Planar Layering?

When parts are irregular or nestable and every extra part per truck matters more than a uniform, hand-picked stack. Packs that are dumped or unloaded by automation are good candidates.

### Does Flexible Layering take longer to compute?

Yes. Searching a full 3D lattice takes more compute time than a flat grid. Results still arrive as ranked options, so you can compare it with faster methods in the same run.

## Related

- [Stacking](https://www.pack-studio.com/features/stacking): Stacking fills nested columns of parts, upright or on their side, then tiles the columns across a carton or rack.
- [Planar Layering](https://www.pack-studio.com/features/planar-layering): Planar Layering builds the pack one flat, repeatable layer at a time, so operators unload it by hand and quality teams count it at a glance.
- [All Pack Studio features](https://www.pack-studio.com/features)
- [How to use Flexible Layering](https://www.pack-studio.com/wiki/flexible-layering)

Book a demo: https://www.pack-studio.com/contact

[^1]: Cost per part, Stacking versus Flexible Layering: 33% lower. Same box and board grade. Source: [Stacking: Minimizing the Shipping Cost for Stamped Parts](https://www.pack-studio.com/post/stacking-minimizing-the-shipping-cost-for-stamped-parts), 2026-08-17.
